FAQ  •  Register  •  Login

What is this springer?

Moderators: Curt!, Pa

<<

milwaukee belle

User avatar

Posts: 923

Joined: Thu Jul 24, 2003 12:01 am

Location: South Provence of FRANCE

Post Sun Sep 06, 2009 4:05 am

Re: What is this springer?

Okay Kurt :
it was just a question of words i didn't found to explain :
ya said " ...the stem is installed at an angle and welded."

this is TRUE .


but THIS IS NOT ENOUGH !

coz the ORIGINAL offset fork HAS THE STEM FLOOR ANGLED TOO !
(the stem still comes to the floor at 90 Degrees )

it ALSO has the lower center of the stem AHEAD about 10 Millimeters on the floor !

so you said "with the original cones : all is Okay "
( about this : i have a SERIOUS doubt , but this is not the subject )
do you believe all the forks you sold go to a restoration ????
they go on CUSTOM-BIKES . 95% of your forks sales is for CUSTOM-BIKES USE .
and do you believe these guys still work with the ball-bearings :lol: ????

i don't say this to " say something bad about kurt " this is not my style .
i let this game to others coz in facts : i am TOO-MUCH HAPPY about all the repop parts you sold me .
i just try to push you in the GOOD direction .
ya say "reproduction-EXACT" ?
okay : so DO THE EXACT repop !
not something lookin'like !
<<

Kurt

User avatar

Posts: 422

Joined: Wed Feb 16, 2005 1:01 am

Location: Tucson Arizona

Post Sun Sep 06, 2009 6:21 am

Re: What is this springer?

No problem Fran-6....all is good between us.

I just didn't want anyone to think that in order to get an offset fork all we did was bend the fork stem. That's how I understood the way you wrote it. Just wanted to set that straight.

As for making a "correct" offset.......for the amount of offset forks I've sold over the years........probably 25+ inline forks to 1 offset.........it's not worth the extra effort as far as I'm concerned

Like I said, the problem only arises when someone wants to use Timken bearings

Kurt
<<

milwaukee belle

User avatar

Posts: 923

Joined: Thu Jul 24, 2003 12:01 am

Location: South Provence of FRANCE

Post Sun Sep 06, 2009 10:36 am

Re: What is this springer?

Kurt wrote:As for making a "correct" offset.......for the amount of offset forks I've sold over the years........probably 25+ inline forks to 1 offset.........it's not worth the extra effort as far as I'm concerned


on this point : i agree and understand . :oops:
<<

milwaukee belle

User avatar

Posts: 923

Joined: Thu Jul 24, 2003 12:01 am

Location: South Provence of FRANCE

Post Tue Sep 08, 2009 10:25 am

Re: What is this springer?

i just read elsewhere somebody saying
" if these forks are rear-bent : it's not coz the factory built them this way ;
it's coz the motors were powerful and the front brake also ... "
something this kind .... :roll:
<<

panic

Post Tue Sep 08, 2009 5:45 pm

Re: What is this springer?

For those whom may be somewhat confused by the huge amount of new and important data:

milwaukee belle has used, merely as a fixed point of reference, an (imaginary) vertical line passing through the spring rod support center on the rear leg. This is useful, as it remains without alteration during the life of the springer and may be used to contrast rear leg lengths (as in #2), and compare trail distances.
However: the legend TRAIL, assigned to the horizontal blue link spanning the distance between the fixed reference (above) and the axle center, is not intended to show the actual trail dimension (which is much smaller), but instead merely how the position of the wheel changes when other features change.
The actual "trail" is not, and cannot be shown in these drawings since that requires the depiction of the wheel radius at its height above the ground plane.
<<

milwaukee belle

User avatar

Posts: 923

Joined: Thu Jul 24, 2003 12:01 am

Location: South Provence of FRANCE

Post Wed Sep 09, 2009 1:21 am

Re: What is this springer?

thanks Panic .
Previous

Return to Knuckles

Who is online

Users browsing this forum: Google [Bot], Yahoo [Bot] and 3 guests

Powered by phpBB © 2000, 2002, 2005, 2007, 2012 phpBB Group.