- Accelerator Pump Diaphragm
- Fits Super E & G and Two Throat Carbs
|
- Accelerator Pump Rebuild Kit
- Fits Super E & G gas carbs
- Includes diaphragm, diaphragm spring, check balls, check ball spring, pump pushrod, and required hardware and o-rings
|
- Accelerator Pump Spring
- Fits Super B, D, E, and G Carbs
- Stainless Steel
|
- Bellows Seal
- Fits Super E and G and Two Throat Carbs
- Nitrile
|
- Bowl gasket
- Fits Super B & D gas carbs
- Sold individually
|
- Bowl Gasket
- Fits Super E & G Carbs
|
- Accelerator Pump Rebuild Kit
- Fits S&S Two Throat Carbs
|
- Fits Super A & B Series Carbs
- Include stainless steel throttle shaft bushings
- Fits forked or wire type float
|
- Carburetor body rebuild kit
- Includes throttle shaft nuts, nylon washers, accelerator pump o-ring, and accelerator pump boot
- Fits Super E Series gas carbs
|
- Carburetor body rebuild kit
- Includes throttle shaft nuts, nylon washers, accelerator pump o-ring, and accelerator pump boot
- Fits Super G Series gas carbs
|
- Fits MGAL and GAL series carbs
- Everything needed to completely rebuild one carburetor
- Fits Super GAL & MGAL Series Carbs
|
- Fits Super A & B
- Everything needed to completely rebuild one carburetor.
- 1983 - Up Wire Type Mechanism
|
- Super A and B gas carbs
- Everything needed to completely rebuild one carburetor
- 1983 and earlier fork type mechanism
|
- Carburetor master rebuild kit
- Fits Super E Series carbs
- Regular gas Inlet
|
- Carburetor master rebuild kit
- Fits Super G Series carbs
- Regular gas Inlet
|
- Fits Super E and G Carbs
- 1966-1982 Big Twin Models
|
- Carburetor Support Bracket
- For Panhead & Knucklehead Engines
- Fits 1948 - 1995 Big Twin
|
- For Super A, B, and D Carbs
- 1966-1984 Big Twin Models
|
- Diaphragm Spring
- .485" X .525", Fits Super E &G Carbs
- Sold individually
|
- O-ring
- .125" ID X .250" OD
- Silicone, 10 Pack
|
- Enrichment Device
- Fits Super B and D Carburetors
- For use with Air Horn Only
|
- Enrichment Plunger Nut
- 7/16-20 X .520" , Brass
- Fits Super E & G Carbs
|
- Enrichment plunger spring
- .228" X .270" X 1.781"
- Stainless Steel Wire
|
- Float Pin
- .096" X 1.170" Brass
- Fits Super E & G Carbs
|
- Float retaining pin
- For fuel and turbo carbs
- Super B and D carbs
|
- Float Retaining Pin
- Gas
- Fits Super A, B, and D
|
- Carburetor Master Rebuild Kit
- Fits Super GBL Series Carbs
- Everything needed to completely rebuild one carburetor
|
- Intermediate and Main Jets
- Various Sizes
|
- Brass
- 5 Pack
- Sits Super B, D, E, and G carbs
|
- Idle Mixture Screw Spring
- Fits B, D, E, & G Carbs
- Stainless Steel Wire
|
- Threaded Fuel Inlet
- Fits Super E & G gas carbs
- .160" I.D.
|
- For wire or forked type float
- Brass, .160"
- Fits Super B and D gas carbs
|
- Super B and D Inlet Seat
- Wire type float, .238" I.D.
- Gas
|
- Bowl gasket
- Fits L-Series carbs
- Pack of 5
|
- Carburetor Body Rebuild Kit
- Fits "L" Series Carbs
- Stainless Steel Throttle Shaft Bushings included
|
- Sizes .084-.120 inch
- Fits All S&S Super Carbs
|
- Sizes .042-.060 Inch
- Fits All S&S Super Carbs
|
- Main Discharge Tube
- Gas carbs
- Fits Super B, E, and G carburetors
|
- Intermediate and Main Jets
- Various Sizes
|
- Carburetor Master Rebuild Kit
- Fits Super MGL Series Carbs
- Everything needed to completely rebuild one carburetor
|
- For wire type float
- Gas carbs
- Fits all Super B, E, and G Turbo Carbs
|
- For forked type float
- Gas carbs
- Fits Super B & D Series Gas Carbs
|
- For wire type float
- Super D, E, and G gas carbs
- For racing only
|
- Overflow Hose
- .125" X .250" X 24"
|
- Used to route gas from overflow fitting on carb to ground
- .125" X .250" X 24"
- 5 Pack
|
- Pump Actuator Arm
- Fits Super E & G Carbs
|
- Pump Actuator Lever
- Fits Super E & G Carbs
|
- O-ring
- 2.187" ID X 3.437" OD
- Silicone, 10 Pack
|
- .390" ID X .510" OD
- Silicone
- 10 Pack
|
- Fit All S&S Super Alcohol, Fuel, and Turbo Carbs
- One each: (0.46", .050", .060"), (.060", .070, .080"), (.080" .090" .100") or One Blank
|
|
